EQUIPMENT    

SEALANT

GEO COMPOSITES

BRIDGE PRODUCTS

 ROOFING PRODUCTS

   SPECS/INSTALLATION INST/MSDS  

   

PATCHING PRODUCTS WHERE TO PURCHASE FAQ NEWS/VIDEOS/LIBRARY

   CONTACT CRAFCO

HOME PAGE  



Improve, maintain and waterproof bridge decks.

“United States Congressional leaders say the number of bridges in need of repair is too high and funding too low.”

“ If you do not take care of what is needed to maintain the condition and performance of an asset, you start creating a backlog of maintenance and capital improvement that needs to be met.”

 


Crafco GeoTac, GeoTac HS, PavePrep SA, and PavePrep TSA are peel-and-stick self-adhesive waterproofing membranes supplied in rolls that are used for waterproofing bridge decks and other paved or structural surfaces before placement of hot mix asphalt concrete wearing surfaces.

GeoTac is an effective waterproofing membrane that is a minimum thickness of 0.065 inch (1.65mm) and is composed of a layer of self-adhesive polymer modified asphalt waterproofing adhesive (with a release liner) bonded to a non-woven polypropylene reinforcing fabric.

GeoTac HS is a higher strength version of GeoTac with increased puncture, tear and temperature resistance (overlay temperature can range up to 350°F (177°C), that is used when increased toughness and durability in the waterproofing installation is desired.

PavePrep SA is a heavy duty high strength waterproofing membrane that is 0.135 inch (3.4mm) minimum thickness and is composed of a flexible, high density asphalt mastic bitumen between a top layer of heat resistant, high strength woven polyester reinforcing fabric and a bottom layer of non-woven heat resistant polyester fabric with a polymer modified asphalt self-adhesive layer and removable release liner. The high strength fabrics provide increased reinforcement and cracking resistance.

PavePrep TSA is composed of the same fabrics and asphalt layers as PavePrep SA, but is thinner with thickness of 0.080 to 0.115 inch (2.0-2.9mm).

BRIDGE DECK
LITERATURE

 

INSTALLATION
INSTRUCTIONS

 
GeoTac MSDS
GeoTac Specs
GeoTac HS Specs
All GeoTac Inst.
Instructions
 
PavePrep SA MSDS
PavePrep SA Specs
PavePrep SA/TSASpecs
All PavePrep Inst.
Instructions
 
 

The Crafco Matrix 501 & 502 Asphaltic Plug Bridge Joint System


The Crafco Matrix 501 & 502 Asphaltic Plug Bridge Joint System
is a pre-measured hot-applied bridge expansion joint system composed of a uniquely formulated polymer modified asphalt binder and select aggregate. Simply level the material and allow to cool. No compaction is required. The Crafco Matrix 501 & 502 joint can be used for expansion, fixed end, and pressure relief joints, in both new construction or rehabilitation projects. Crafco Matrix 501 & 502 can be installed on skews up to 30 degrees (up to 45 degrees for low traffic pavements). Crafco Matrix 501 & 502 joints are low cost, quick, and easy to install and maintain. The Crafco Matrix 501 & 502  joint meets the requirements of ASTM D6297, Standard Specification for Asphaltic Plug Joints for Bridges.
Matrix 501 MSDS
Matrix 501 Inst.
Instructions
Ultraseal Bridge Products

 

  

  

EQUIPMENT    

SEALANT

GEO COMPOSITES

BRIDGE DECK PRODUCTS

 ROOFING PRODUCTS

   SPECS/INSTALLATION INST/MSDS

   

PATCHING PRODUCTS WHERE TO PURCHASE FAQ NEWS/VIDEOS/LIBRARY

   CONTACT CRAFCO

  HOME PAGE

420 N. Roosevelt Ave., Chandler, AZ 85226 • 1.800.528.8242 / 602.276.0406 / Fax 480.961.0513